EU Machinery Regulation: Get Ready for 2027 (FAQs)
Authored by Livia Kecerova, Senior Team Leader, Adherent
Key Insight
From 20 January 2027, every individual unit of machinery placed on the EU market must comply with Regulation (EU) 2023/1230, however long its model has been sold. Standards cited under the Directive will no longer give an automatic presumption of conformity, and new requirements, notably protection against corruption, apply even though the dedicated standard (EN 50742) is not yet harmonised. Manufacturers should confirm product classification and conformity assessment routes now, and update their risk assessments, declarations, marking and instructions.
Table of Contents
- Introduction
- Scope, timing and responsibilities
- Conformity assessment and Annex I
- Harmonised standards
- Cybersecurity, software and AI
- Documentation
- Priorities before 20 January 2027
- Frequently Asked Questions
- Sources and references
Introduction
We are in the final countdown to 20 January 2027, when the EU Machinery Regulation (EU) 2023/1230 (MR) applies and replaces the framework of Directive 2006/42/EC. On 5 November 2026, the Expert Group on Machinery formally endorsed the first chapters of the Commission’s guide to the application of the MR, issued as a temporary and partial publication. Yet manufacturers still face a transition gap and considerable uncertainty. This FAQ blog answers the 15 questions often voiced by manufacturers, importers, distributors and integrators.
The sequence of questions follows a typical compliance (checklist) process: what is covered, when the rules apply, how conformity is assessed, which standards to use, what the new cybersecurity and AI requirements demand, and what must change in your documentation.
Throughout, this resource is based on and references the latest consolidated text of the Regulation (27 July 2026), which includes the amendments made by Regulation (EU) 2024/2748 (on emergency procedures) and Regulation (EU) 2026/1744 (the AI Omnibus), as well as EU Commission’s Guide to application of the Machinery Directive 2006/42/EC, ed. 2.3 of April 2024, which remains relevant.
Scope, timing and responsibilities
Q1. Does the Regulation apply to your product? What falls within its scope, and how is software classified?
The Regulation covers machinery, five types of “related products” and partly completed machinery. The product families are the same as under the Directive, but the definitions now clearly cover software and digital components.
Article 2(1) lists the products covered, and Article 3 defines them:
| Product | Definition in short (Art. 3) | What is new or worth noting |
|---|---|---|
| Machinery Art. 3(1) | An assembly with a drive system other than direct human or animal effort, of linked parts at least one of which moves, joined for a specific application. Also covers assemblies missing only connection components or application software, assemblies functioning as an integral whole, and manually powered lifting machinery. | New point (f): an assembly missing only the upload of the software for its specific application is already machinery. |
| Interchangeable equipment Art. 3(2) | A device the operator assembles with machinery or a tractor after it is put into service, to change its function or add a new one; not a tool. | Fitted by the operator to machinery or an agricultural or forestry tractor to change or add a function; tools are not included. |
| Safety components Art. 3(3) | A physical or digital component, including software, independently placed on the market, that fulfils a safety function, whose failure endangers persons, and which is not needed for the product to function. | Explicitly a “physical or digital component, including software”, placed independently on the market. A ‘safety function’ is defined in Art. 3(4). |
| Lifting accessories Art. 3(5) | A component or equipment, not attached to the lifting machinery, that holds the load and is independently placed on the market. | Includes slings and their components. |
| Chains, ropes and webbing Art. 3(6)–(8) | Chains, ropes and webbing designed and constructed for lifting, as part of lifting machinery or lifting accessories. | Designed and constructed for lifting purposes. |
| Removable mechanical transmission devices Art. 3(9) | A removable component transmitting power between self-propelled machinery or a tractor and other machinery, joined at the first fixed bearing. | A device placed on the market with its guard counts as one item. |
| Partly completed machinery Art. 3(10) | An assembly that cannot by itself perform a specific application and is only intended to be incorporated into machinery or other equipment, thereby forming machinery. | Cannot perform a specific application by itself; only intended to be incorporated into machinery. |
Machinery, the related products and partly completed machinery are together referred to as ‘products within the scope of this Regulation.’
What it means: Software now falls squarely within the remit of the MR. Annex II, the indicative list of safety components, includes:
- software ensuring safety functions (point 18); and
- safety components with fully or partially self-evolving behaviour using machine learning approaches (point 19).
If safety software is placed on the market on its own, it is considered a safety component, with all the manufacturer’s obligations attached to it.
Q2. What is excluded, and where have the borderlines moved?
Article 2(2) keeps most of the Directive’s exclusions but changes the wording in several places, for example for vehicles, aircraft, 3D printers, electrically operated furniture and radio equipment.
Article 2(2) lists 17 exclusions, points (a) to (q). They include safety components supplied by the original manufacturer as identical spare parts, fairground equipment, weapons, seagoing vessels, military and police machinery, temporary laboratory research machinery, mine winding gear and machinery moving performers. It also contains some conditional exclusions, such as:
- means of transport and vehicles covered by their own type-approval rules (for example, motor vehicles and two- or three-wheel vehicles); machinery mounted on those vehicles, however, remains in scope;
- electrical and electronic products insofar as they fall under the Low Voltage Directive 2014/35/EU or the Radio Equipment Directive 2014/53/EU. The exclusion covers, among others, household appliances (but not electrically operated furniture) and office machinery (but not additive (3D) printing machinery);
- high-voltage switchgear, control gear and transformers;
- aeronautical and nuclear products, under the conditions specified.
What it means: Where a more specific EU harmonisation legislation covers the risks addressed by Annex III, the Machinery Regulation does not apply in relation to those risks. For connected household and IT products, for example, the Low Voltage and Radio Equipment Directives determine whether the product is excluded.
Q3. Does every unit placed on the market from 20 January 2027 need to comply?
In short, yes. The test applies to each individual unit, not to the model or type. A unit first made available on the EU market on or after 20 January 2027 must comply with the Regulation, even if identical units were lawfully sold under the Directive.
§73 of the Machinery Directive Guide confirms the same principle: placing on the market “refers to each individual item of machinery or partly completed [machinery] and not to a model or type”.
Q4. Can an existing model continue to be sold under the Directive after 20 January 2027?
Only units already placed on the market before that date.
Member States must not impede the making available of products that were placed on the market in conformity with the Directive before 20 January 2027 (Art. 52(1)). Those units do not need to be reassessed under the Regulation.
“Placing on the market” means the first making available of a product on the Union market. “Making available” means any supply for distribution or use in the course of a commercial activity, whether paid or free of charge.
What it means: The transitional provision in Article 52(1) protects individual products, not models. Machinery lawfully placed on the EU market before the Regulation applies may continue to be made available. In addition, EC type-examination certificates and approval decisions issued under Article 12 of the Directive remain valid until they expire.
Conversely, units that remain in the manufacturer’s own warehouse and have not yet been supplied for distribution or use on the EU market are not placed on the market merely because they were manufactured before the deadline. The decisive factor is when each individual unit is first made available for distribution or use on the EU market, not when the design was approved or the machinery manufactured. §73 of the Machinery Directive Guide also notes that a product merely transferred to your authorised representative, so that it can fulfil your obligations, is not yet placed on the market.
If such units are placed on the EU market on or after 20 January 2027, they must comply with Regulation (EU) 2023/1230.
Q5. Substantial modification: when does one become a manufacturer?
Under Articles 3(16) and 18, the manufacturer’s obligations kick in whenever one modifies machinery after it has been placed on the market or put into service, in a way the original manufacturer did not foresee or plan, and the change creates a new hazard or increases an existing risk that requires new safeguarding like addition of guards or protective devices whose processing necessitates modification of the existing safety control system.
What it means: This applies to anyone – manufacturer, importer, integrator or end user – who makes such a change to a product already on the market or put into service. They must apply Article 10 obligations and the relevant conformity assessment procedure under Article 25 to each machine so modified. The only exception is a non-professional user who modifies their own machinery for their own use.
Separately, importers and distributors are treated as manufacturers if they place a product on the market under their own name or trademark, or modify it in a way that may affect compliance.
Software updates, retrofits and line rebuilds can all count, because the definition expressly covers modifications made by digital means.
Q6. Partly completed machinery: what changes for the declaration of incorporation and assembly instructions?
As under the Directive, partly completed machinery does not carry the CE marking. What has changed is the depth of the evidence trail. An EU declaration of incorporation is required, together with much more detailed assembly instructions, which may now be digital. These must describe precisely what is actually supplied, which in turn puts pressure on the manufacturer’s own component suppliers.
What it means: Under Article 11, before placing partly completed machinery on the market, the manufacturer must:
- meet the relevant essential health and safety requirements (EHSRs) of Annex III;
- draw up the technical documentation under Annex IV, Part B, and the EU declaration of incorporation under Article 22 and Annex V, Part B;
- keep both for at least 10 years and, where relevant, provide source code or programming logic to national authorities on reasoned request;
- mark the product with its designation, year of construction, model, series or type and any serial number, plus the manufacturer’s postal address and website, email address or other digital contact; and
- supply assembly instructions under Annex XI (Art. 11(7)), covering items ranging from drawings and assembly instructions to warnings about foreseeable misuse.
The assembly instructions may be issued in digital format, provided that the manufacturers:
- mark how to access them;
- make them printable, downloadable and savable; and
- keep them online for at least 10 years.
If the buyer requests a print copy at the time of purchase, it must be provided free of charge within one month. The instructions must also be clear, understandable and legible.
The declaration of incorporation can be supplied as a document, or as an internet address or machine-readable code given in the assembly instructions. A digital declaration must remain accessible online for at least 10 years.
Conformity assessment and Annex I
Q7. Which six product categories always need a notified body?
The six categories listed in Annex I, Part A. For them self-certification is no longer sufficient, even where harmonised standards are applied in full. Instead, under Article 25(2), products in Annex I, Part A must follow one of three procedures, each involving a notified body:
- EU type-examination (module B, Annex VII), followed by conformity to type based on internal production control (module C, Annex VIII);
- full quality assurance (module H, Annex IX); or
- unit verification (module G, Annex X).
The six Part A categories are:
- removable mechanical transmission devices, including their guards;
- guards for removable mechanical transmission devices;
- vehicle servicing lifts;
- portable cartridge-operated fixing and other impact machinery;
- safety components with fully or partially self-evolving behaviour using machine learning approaches ensuring safety functions;
- machinery with embedded systems with fully or partially self-evolving behaviour using machine learning approaches ensuring safety functions that have not been placed independently on the market, in respect only of those systems.
What it means: Anyone producing products in any of these six categories must engage a notified body (NB) notified for the relevant category. Once the procedure is complete, the notified body’s identification number follows the CE marking (Art. 24(3)).
Q8. When can an Annex I Part B product be self-certified using harmonised standards?
Only if the harmonised standards or common specifications applied are specific to that category and cover all relevant EHSRs applicable to the product. Article 25(3) offers four routes for the 19 categories in Annex I, Part B:
| Route | Module (Annex) | Notified body | Condition |
|---|---|---|---|
| Internal production control | A (Annex VI) | No | Only with category-specific harmonised standards or common specifications covering all applicable EHSRs |
| EU type-examination + conformity to type | B + C (Annexes VII, VIII) | Yes | None |
| Full quality assurance | H (Annex IX) | Yes | None |
| Unit verification | G (Annex X) | Yes | None |
Products not listed in Annex I always use module A, internal production control (Art. 25(4)).
What it means: “All relevant EHSRs” now includes protection against corruption (1.1.9) and the new control-system requirements (1.2.1) where applicable. If the harmonised standards or common specifications for your Part B product do not cover all applicable EHSRs, or their Official Journal citations contain restrictions that leave applicable requirements uncovered (see Q9), Module A is no longer an option.
Connected products, such as logic units ensuring safety functions and protective devices designed to detect persons, are directly affected while no standard covering 1.1.9 is cited.
Harmonised standards
Q9. Will harmonised standards cited under the Machinery Directive still give presumption of conformity after 20 January 2027?
Not automatically. Every citation under the Directive loses its legal effect on 20 January 2027. From then on, presumption of conformity under the Regulation comes only from standards whose references are published in the Official Journal under the Regulation (Art. 20(1)).
The Commission plans to re-cite most current standards under the Regulation in one of three forms: as they are, as covering new requirements, or with restrictions where a new or changed EHSR is not covered. Once the list is published, check it for restrictions: a restricted citation gives presumption of conformity only for the EHSRs it covers. At the time of writing, the first list had not yet been published.
My previous blog examined the gap arising from the lack of harmonised standards cited under the Regulation.
Q10. Machinery and the Low Voltage Directive: where do standards such as EN 61800-5-1 fit?
Machinery with an electricity supply must meet the safety objectives of the Low Voltage Directive (LVD), but its conformity assessment is governed solely by the Machinery Regulation (Annex III, 1.5.1). A standard harmonised under the LVD, such as EN 61800-5-1 (adjustable speed electrical power drive systems – electrical, thermal and energy safety requirements), can therefore support compliance as evidence of the state of the art. On its own, however, it does not give presumption of conformity under the Machinery Regulation.
Cybersecurity, software and AI
Q11. Protection against corruption: what do EHSRs 1.1.9 and 1.2.1 actually require?
Safety-relevant connections, hardware, software and data must be protected so that accidental or intentional corruption cannot lead to a hazardous situation. The machine must be able to show which safety software it runs and keep evidence of interventions. The Commission’s new guide chapter on these requirements was formally endorsed by the Expert Group on Machinery on 5 November 2026 and subsequently made public.
Although partial and subject to further refinement, the guide describes section 1.1.9 as protection against unauthorised or harmful modification of the integrity or authenticity of safety-relevant signals and data. It requires an assessment of the machine’s exposure, vulnerabilities and threats across its lifecycle. Typical exposures include remote access, cloud connectivity and unprotected interfaces. The requirement covers safety only, not data confidentiality, intellectual property or business continuity.
Manufacturers are expected to identify and implement appropriate countermeasures based on the machinery’s risk assessment, taking account of information security methods, specific assumptions and the state of the art.
Examples of potential countermeasures against accidental or intentional corruption include:
- protection of service interfaces;
- signature verification of software updates;
- cryptographic message authentication codes;
- hashes;
- checksums, which protect against accidental corruption only;
- organisational measures, such as specific procedural instructions.
For traceability, appropriate state-of-the-art measures should be used to ensure that all changes and safety-related interventions, whether authorised or not, can be traced and recorded. The guide refers to the concept of the state of the art as explained in §161 and §162 of the Guide to application of the Machinery Directive, Edition 2.3.
Furthermore, under Annex III, section 1.2.1(f), a tracing log of interventions and versions of safety software uploaded after placing on the market or putting into service must be enabled. According to the guide, each event must be kept for at least five years after the software change, so that conformity can be demonstrated on a reasoned request from a competent national authority.
Q12. EN 50742 (Safety of machinery – Protection against corruption) is not yet harmonised: can IEC 62443 (Security for industrial automation and control systems) be relied on?
Yes, as evidence of the state of the art, but not for the purpose of presumption of conformity under the Regulation. For the safety components and logic units within its scope, the notified bodies’ Recommendation for Use CNB/M/11.073 confirms that, pending EN 50742, standards representing the state of the art, such as IEC 62443, may be used.
EN 50742 is being prepared by CLC/TC 44X under standardisation request M/605. It addresses Annex III, section 1.1.9, over the whole product lifecycle and excludes the functional safety of control systems. The final draft (FprEN 50742) dates from July 2026. The CENELEC formal vote stage was recorded as completed on 9 October 2026, and publication is listed for 19 November 2026. National standards bodies then have up to six months to announce it and twelve months to adopt it. EN 50742 will, however, give presumption of conformity only once its reference is published in the Official Journal under the Regulation.
Q13. AI-enabled machinery after the AI Omnibus: what changes and when?
The AI Omnibus, Regulation (EU) 2026/1744, published on 24 July 2026 and in force since 27 July 2026, moves machinery to a sector-specific approach under the AI Act, Regulation (EU) 2024/1689. AI-specific health and safety requirements for machinery will be added to the Machinery Regulation itself by delegated acts, which must apply by 2 August 2028.
What it means: The Machinery Regulation was moved from Section A to Section B of Annex I to the AI Act (the list of Union harmonisation legislation relevant to high-risk AI systems). This largely removes parallel (double) obligations, although the AI Act remains relevant for classification, supervision and enforcement. The Commission must adopt delegated acts adding to Annex III of the Machinery Regulation health and safety requirements for AI systems that are high-risk under Article 6(1) of the AI Act because they are a safety component of a machinery product, or are themselves such a product.
Until Machinery Regulation standards or common specifications for high-risk AI exist, products that comply with AI Act harmonised standards or common specifications are presumed to conform to the AI-related Annex III requirements.
Documentation
Q14. What must change in the technical documentation, marking, instructions and authorised representative mandate?
Machinery and related products first placed on the EU market or put into service from 20 January 2027 must comply with the Regulation, including the requirements for the EU declaration of conformity, technical documentation, marking and instructions. Authorised representative mandates may also need review.
Declaration of conformity
The EC declaration must be replaced with an EU declaration of conformity following Annex V, Part A, and the copy in the instructions must be updated. Harmonised standards must be cited together with the date their reference was published in the Official Journal. If a standard was applied only in part, the declaration must state which parts were applied. Where a notified body was involved, its name, number and certificate reference must also be given.
Technical documentation
The technical documentation must include the documentation on risk assessment, listing the applicable EHSRs, the protective measures for each and the residual risks (Annex IV, Part A, point (b)). The risk assessment must now also cover hazards from the intended evolution of self-evolving behaviour, and risks from interaction between machines forming an assembly.
Where applicable, new elements include:
- the source code or programming logic of safety-related software, to be made available on reasoned request; and
- for sensor-fed, remotely driven or autonomous machinery, a description of the system’s capabilities, limitations, data, development, testing and validation.
Where Annex ZA of a C-type standard does not cover a new EHSR, for example 1.1.9, that EHSR must be addressed separately in the technical file.
Marking
- Model, series or type, year of construction, and serial or batch number where one exists.
- Name, postal address and website, email address or other digital contact.
- The notified body’s number after the CE marking, where the Annex I procedure involves one.
Instructions for use
- New contents include a description of the intended use, the uncertainties and operating conditions for noise declarations, the means for the immediate and gentle rescue of persons, and data on hazardous-substance emissions where relevant.
- The EU declaration of conformity, or the internet address or machine-readable code where it can be accessed, must be included.
- Digital instructions are allowed if access is marked on the product, they can be printed, downloaded and saved, and they remain accessible online throughout the expected lifetime of the machinery or related product and for at least 10 years after placing on the market.
- A paper copy must be supplied free of charge within one month if requested at the time of purchase.
- Products that non-professional users could use must come with the essential safety information on paper.
Authorised representatives
Two obligations can no longer form part of the authorised representative’s mandate (Art. 12(1)):
- designing and constructing the product in line with the EHSRs (Art. 10(1)); and
- drawing up the technical documentation.
The mandate must at least allow the representative to keep the documentation and declaration for 10 years, provide information to authorities on reasoned request, and cooperate with them on actions to eliminate risks.
Priorities before 20 January 2027
Q15. What should manufacturers prioritise before January 2027?
Manufacturers should start by classifying their products and establishing the date on which each individual unit will be placed on the EU market. They should then review the relevant Annex III essential health and safety requirements, update risk assessments and engineering evidence, confirm the applicable conformity assessment route, and revise declarations, marking and instructions where necessary. The objective is not simply to refresh paperwork: the technical assessment and the documents supplied with the product must consistently demonstrate conformity with the Regulation.
Frequently Asked Questions
When does the EU Machinery Regulation apply?
From 20 January 2027, when it replaces Directive 2006/42/EC. It applies to each individual unit placed on the EU market from that date, regardless of when the model was first sold.
Can machinery placed on the market under the Directive still be sold after 20 January 2027?
Yes. Units placed on the market in conformity with the Directive before 20 January 2027 may continue to be made available without reassessment (Art. 52(1)). Units still in the manufacturer’s warehouse are not covered.
Is software covered by the Machinery Regulation?
Yes. Software ensuring safety functions that is placed on the market on its own is a safety component. Safety components with self-evolving, machine-learning behaviour are in Annex I, Part A and always need a notified body.
Does EN 50742 give presumption of conformity for protection against corruption?
Not yet. It will do so only once its reference is published in the Official Journal under the Regulation. Until then, EN 50742 and IEC 62443 can be used as evidence of the state of the art.
When do AI-specific requirements for machinery apply?
The Commission’s delegated acts adding AI requirements to Annex III must apply by 2 August 2028. Before Machinery Regulation standards are made available, AI Act harmonised standards give presumption of conformity for those requirements.
Sources and references
This article is general compliance information, not product-specific legal opinion. Check the latest consolidated legislation, Official Journal citations and Commission updates before relying on any time-sensitive status.
Further sources:
- European Commission (DG GROW), Guide to the application of the Machinery Regulation (EU) 2023/1230 – Temporary and partial publication: Annex III 1.1.9 and 1.2.1(a) & (f) (protection against corruption and cyber-safety)
- EU Artificial Intelligence (AI) Act portal
- European Commission, Low Voltage Directive (LVD) harmonised standards
- iTeh Standards: EN 50742:2026 project status
- SafeMech (Douglas Florence), Gap analysis for transition of equipment declared in conformity with Machinery Directive 2006/42/EC to Machinery Regulation (EU) 2023/1230

See Adherent in Action
Discover how agentic AI is reshaping product compliance for global enterprises.
Authors

Livia Kecerova
Senior Team Leader, Global Regulatory Compliance
Leading global regulatory compliance with expertise in industrial machinery, gas appliances and power generation equipment, alongside extensive experience in product safety, market access and emerging regulatory requirements.
